Operating Instructions Programat® EP 3000 G2Valid as of Software Version 6.0
102.1.6 Risks and dangers Do not carry the furnace by the cooling tray. 2.1.7 Risks and dangersDo not carry the furnace head by the cables, since t
112.2 Health and safety instructionsThis furnace has been designed according to EN 61010-1 and has been shipped from the manufacturer in excellent c
123. Product Description3.1 Components The Programat EP 3000/G2 comprises the following components:– Furnace base with electronic controls– Furn
134. Installation and Initial Start-Up4.1 Unpacking and checking the contentsThe packaging provides the following advantages:– Reusable packaging–
14Step 2: Mounting the furnace headThe complete furnace head (58) is best mounted with the rear panel of the furnace pointing towards the user. Lift t
15Step 3: Placing the firing plate for the investment ring (5)The firing plate for the investment ring (5) can now be placed on the firing plate holde
16Secure the heater plug (28) with the plug fuse (27) by turning it until the heater plug (28) has been secured.Step 5: Mounting the hood (36)Once all
174.4 Removing the furnace head Before the hood (36) is removed, the furnace has to be switched off and the power cord disconnected from the power
184.5 Initial start-up1. Connect the power cord with the wall socket. 2. Put the On/Off switch (11) at the rear of the furnace on position „I“ a
195. Operation and Configuration 5.1 Introduction to the operationThe Programat EP 3000/G2 is equipped with a graphical display with backlighting. T
205.4 Adjustable parameters and possible value ranges Symbol Parameter Value range °C Value range °F P Program number 1-300 B Stand-by
215.5 Settings, special programs and information This screen can be selected via the Settings / Information key (78) if no program is active.The cu
22 The user code (6725) is required for some Settings. 5.5.2 Special programs5.5.2.1 Vacuum test programWith this vacuum test program, the performanc
235.6 Explanation of the symbols on the displayPage Description1/11 Serial number 2/11 Software version 3/11 Firing hours of the f
24Symbol nameInformation SettingsMeaningFor selecting the Infor-mation screen.For selecting the Settings screen.SymbolFor additional explanations on
256. Practical Use6.1 Switching on/offPut ON/OFF switch on position “I”. The furnace conducts an auto-matic self-test, which will be indicated in the
6.3 Press programs6.3.1 Pressing using an Ivoclar Vivadent program 6.3.2 Selecting the press program typeOnce the Pressing mode has been selected, th
276.3.9 Notes on the individual press programsFor the abort speed, we recommend using a value of 300 µm/min in the layering technique and 150 µm/min i
286.4.4 Stopping the running programPress the STOP key once to pause a running program. The green LED in the START key blinks. Press the STOP key twic
297. Maintenance, Cleaning, and DiagnosisThis chapter describes the user maintenance and cleaning procedures for the Programat EP 3000/G2. Only those
3Views of the Furnace, List of Parts 4 1. Introduction / Signs and Symbols 81.1 Preface 1.2 Introduction 1.3 Notes regarding the Operat
30 7.2 CleaningThe furnace may only be cleaned when it is cool, since there is a burn hazard. Do not use any cleaning solutions. The following p
317.6 Replacing the press plungerIn order to facilitate replacing the press plunger, the following procedure is recommended.1. Remove the screw (20
328. What if ...This chapter will help you to recognize malfunctions and take appropriate measures or, if possible and acceptable, to perform some si
33Please contact the Ivoclar Vivadent After Sales Service, if one of the following error messages is being displayed: 25, 2943, 44, 45, 46, 47, 4854,
348.2 Technical malfunctionsThese malfunctions may occur without an error message being displayed.*If there are any questions, please contact the Iv
359. Product Specifications9.1 Delivery form– Programat EP 3000/G2 – Programat fring tray Kit– Firing plate – Automatic Temperatur Checking Set
10. Appendix10.1 Program tableTwo program tables (°C / °F) are enclosed in these Operating Instructions. If not, please contact your local Ivoclar
3710.2 Menu structure10.2.1 Selecting the operation mode and program type10.2.2 Firing programs
10.2.3 Press programs 3810.2.4 Settings / Information
39
4List of parts1 Sealing surface2 Furnace head sealing ring3 Insulation4 Thermocouple5 Firing plate 2 6 Display 7 Frame plate8 QTK heat
Ivoclar Vivadent AGBendererstrasse 2FL-9494 SchaanLiechtensteinTel. +423 235 35 35Fax +423 235 33 60www.ivoclarvivadent.comIvoclar Vivadent Pty. Ltd.
5List of parts712395840253856346102335 3658206333
63243592264626522616311363739121353191211131519532117161846 49 2666 30 60 67 29 27 28 11
7Control unit:70 Program key71 ESC key72 ENTER key73 START key74 Start LED75 STOP key76 Plus key77 Minus key78 Settings / Information79 Cursor key rig
81. Introduction / Signs and Symbols1.1 PrefaceDear CustomerThank you for having purchased the Programat EP 3000/G2. It is a state-of-the-art furnac
92. Safety FirstThis chapter is especially important for personnel who work with the Programat EP 3000/G2 or who have to carry out maintenance or repa
Commentaires sur ces manuels